How to set up an electrolux gas water heater

Geyser Electrolux

Initially, all Electrolux products were manufactured in Sweden. The constant increase in production capacity led to the fact that the company's representative offices and factories were opened in many countries.

Russian consumers can buy Electrolux geysers produced in China. Factories carry out mandatory testing of flow-through boilers and check for compliance with high quality standards.

Advantages and disadvantages

Instantaneous water heaters from this company are very popular. Everyone can choose a model depending on their requirements and budget. Different Electrolux speakers differ in price, power, and type of ignition. But they all have several advantages that attract users:

Additional Information! An important advantage of these water heaters is the presence of a draft sensor. If it is absent or if reverse draft occurs, the unit turns off. This prevents gas from entering the room.

The disadvantages of some models of these water heating devices include the impossibility of using them with poor water pressure - the column simply will not light up. It is also difficult to ignite the unit in the absence of traction. But these are the disadvantages of any geysers. If we talk about Electrolux, we can note that they are assembled in China, which may reduce their quality.

How to use an Electrolux speaker

All Electrolux gas water heaters operate in automatic mode. The internal structure is thought out to the smallest detail, making operation as comfortable as possible. When the DHW tap is opened, the automatic system is activated and the main burner is ignited. Hot water reaches the consumer within 10-15 seconds. After closing the tap, the flame dies out.

How to turn on an Electrolux speaker

Almost all leading manufacturers of instantaneous gas water heaters indicate in their operating instructions that installation must be performed by a qualified specialist. In domestic joint ventures and SNiP there is a similar instruction. In accordance with existing standards, connecting with your own hands is prohibited. If you perform a self-installation, then the next time you contact a service center, you should not expect free service. You will have to pay for all work, even if the warranty period has not yet passed.

According to current regulations, the connection can be made by:

representatives of the company that sold the water heater;

Poor water heating.

The main burner goes out during operation.

There is a smell of gas.

• gas service specialists.

A mark and seal is placed in the boiler passport about connecting and putting the device into operation.

There are several basic connection rules:

installation is carried out in accordance with the rules described in SNiP and SP;

the first launch is carried out in the presence of a Gas Service inspector;

be sure to withstand gaps between the stove, refrigerator, and sink;

installation is carried out in strict accordance with the gas supply project;

The column is supplied with fastening elements and an anchor plate. The column is hung on a wall made of dense solid building materials.

How to set up an Electrolux speaker

For adjustment, there are mechanical regulators for the flow of water and gas on the front side of the water heater casing. Most Electrolux speakers have an LED display connected to a heating sensor that shows the water temperature.

To change the power, increase or decrease the gas supply, changing the intensity of the flame, focusing on the digital indicators displayed on the screen.

In the Electrolux gas water heater with flame modulation, adjustments are made according to a different principle. The user sets the required water heating temperature. The programmer independently changes the burner power, adapting to the actual pressure in the water supply system.

How to clean an Electrolux speaker

There are several parts that are most susceptible to contamination:

heat exchanger of the Electrolux column - inside the tubes become overgrown with scale, outside the radiator is covered with soot;

You can clean an Electrolux geyser yourself at home only after the factory warranty has expired. Before this period, it is better to contact the service center to receive free service.

During the repair, the technician will remove the column casing, disconnect the heat exchanger and remove the burner. The coil is washed using special chemicals under pressure. The radiator fins are washed with ordinary soapy water. The burner is cleaned with a metal awl. The work is carried out by a qualified specialist who has access and the appropriate license.

How to use the Electrolux GWH 275, 285, 350 geyser?

To start using the Electrolux geyser, you need water to get into the system. To do this, first of all, open the tap and drain a little water. It is important to inspect all pipe connections for leaks.

After this, the gas valve opens. In this case, a characteristic sound of gas entering the system will be heard. After this, you can turn on the tap, from which heated water should flow. The tap opens immediately to its maximum. If the water pressure is strong enough, you will hear the crackling sound of the piezo ignition spark in the column and the sound of gas igniting. For the water heater to work, the pressure must be in the range from 0.15 to 10 atmospheres. After a short time the water will heat up. If the column is new, the water may have a slight smell of machine oil, which will wash off over time.

When using an Electrolux gas water heater, it is not recommended to dilute heated water with cold water. When you turn on cold water, resistance to hot water is created, the flow decreases, and the column may go out. You need to set a comfortable temperature level in advance and adjust it as needed on the column itself. To make the water a little hotter, you can reduce the water flow. But at the same time, if the pressure is too low, the flame will automatically go out.

Regular use

Geysers from left to right Electrolux GWH 275, 285, 350

To extend the life of your Electrolux geyser, it is important to follow several recommendations when using hot water.

The most expensive part of the column is the thermostat. In Electrolux 275, 285 and 350 water heaters, the heat exchanger is made of copper. It is constantly in contact with hot water, so scale forms on it. It is not recommended to set the maximum water temperature. The optimal temperature for work is 45-50 degrees.

Using the tap to the right of the display, you need to limit the water pressure in the column. This will avoid sudden pressure changes in the structure.

If you know that the hardness of your water is high, it is advisable to additionally install a purification system. Calcium and magnesium salts contained in such water quickly create scale in the thermostat. Installing a filter at the inlet of the device will extend the life of the device.

Even if you follow all the recommendations, scale will still appear. According to the instructions, you need to clean the Electrolux column once a year. It should only be performed by specialists. Workers clean the thermostat from scale and the burner from carbon deposits.

Safety precautions

Any gas equipment requires compliance with safety regulations. Before starting work, it is important to carefully read the official instructions.

Here are the main excerpts from these instructions:

• Electrolux 275, 285 and 350 columns are equipped with gas attenuation control and water temperature limitation.
• First of all, when using a gas water heater for a long time, you should check the chimney draft from time to time. To do this, bring a match to it and determine the presence of air flow by the movement of the flame. Gas workers have special instruments to measure traction force. It is recommended to check once every three months.
• For safety reasons, the window must be open during operation of the column. A two-centimeter gap is made at the bottom of the room door.
• Install water heaters in a place protected from access by small children. It is prohibited to make changes to the design yourself. Some parts of the water heater may be hot and you may get burned.
• If you smell gas in the room, you should immediately put out the fire, turn off the power to the heater, turn off all electrical appliances and call emergency services. Do not obstruct access to gas pipes and equipment or tie clotheslines to them.
• If the column is installed in a room without heating, in cold weather, when it is not in use, you need to remove water from it.

Advantages

Geysers Electrolux 275, 285 and 350 have a number of advantages compared to other models of water heaters:

• Low price, simple design and high reliability. The absence of a large number of fancy electronics reduces the likelihood of device failure.
• Large and bright display. There is also a battery charge indicator on it, which allows you to replace them in time.
• Quiet operation. Quiet start and low flame noise.
• High speed of water heating.
• Ability to work with low water pressure.
• Easy to find components. Electrolux 275, 285 and 350 columns are among the most popular water heaters. If repair or replacement is necessary, you can easily find the necessary parts.
• High performance. Electrolux 275, 285 and 350 water heaters can heat 10, 11 and 14 liters per minute, respectively.
• There is protection against gas extinction and water overheating.
• Large and convenient gas level and pressure regulators.

One of the disadvantages is that the throttle control knob is too sensitive. And a feature of all geysers is the need for high water pressure, without which it simply cannot start.

If you install the Electrolux geyser correctly and follow safety precautions when using it, it will regularly supply you with hot water and will last a long time. Over time, users get used to the operating features of gas water heaters and consider them the best choice.

Source: https://boilervdom.ru/gaz-kolonki/firma/kak-polzovatsya-gazovoj-kolonkoj-elektrolyuks-275-285-350.html

Electrolux column - malfunctions and methods for eliminating them

The operating instructions indicate common causes of water heater failure. Judging by consumer reviews, the Electrolux flow-through gas water heater is generally a fairly reliable water heater that rarely fails.

Common malfunctions of the Electrolux gas instantaneous boiler are described in the table:

What caused the problem

The burner does not turn on.

• No gas supply.
• The water supply pipeline is blocked.
• The batteries are dead or incorrectly installed.

• You should open the gas supply valve and cold water supply to the column.
• Open the hot water supply.
• Replace batteries. When using new batteries, check that they are installed correctly.

Advantages

Geysers Electrolux 275, 285 and 350 have a number of advantages compared to other models of water heaters:

• Low price, simple design and high reliability. The absence of a large number of fancy electronics reduces the likelihood of device failure.
• Large and bright display. There is also a battery charge indicator on it, which allows you to replace them in time.
• Quiet operation. Quiet start and low flame noise.
• High speed of water heating.
• Ability to work with low water pressure.
• Easy to find components. Electrolux 275, 285 and 350 columns are among the most popular water heaters. If repair or replacement is necessary, you can easily find the necessary parts.
• High performance. Electrolux 275, 285 and 350 water heaters can heat 10, 11 and 14 liters per minute, respectively.
• There is protection against gas extinction and water overheating.
• Large and convenient gas level and pressure regulators.

One of the disadvantages is that the throttle control knob is too sensitive. And a feature of all geysers is the need for high water pressure, without which it simply cannot start.

If you install the Electrolux geyser correctly and follow safety precautions when using it, it will regularly supply you with hot water and will last a long time. Over time, users get used to the operating features of gas water heaters and consider them the best choice.

Preparing to set up a water heater

Although there are instructions for the Bosch, Selena and Neva gas water heaters on how to set them up correctly, not everyone understands how to do this. Having made a mistake at the very beginning, the device begins to work not as it should. You should start by regulating the water supply.

First of all, adjust the water regulation. If you do it at the last moment, then all the settings will be incorrect. The flow must be the smallest . The values ​​can be found in the documentation, they are usually 6, 10 and 12 liters.

The main thing is that there is only one tap for work.

Starting the device and adjusting the temperature

To correctly set up hot water in the device, you must:

• Open the hot water mixer fully;
• Using the water switch, select the required temperature value;
• Close the tap.

According to the advice of professionals:

• Wait for the moment when the pressure in the line drops, but the column will still work;
• Turn the water toggle handle to the maximum;
• Turn the gas regulator to the minimum value until the temperature is as desired.

For final preparation, it is worth adjusting the gas supply. To do this, you need to look at the technical data sheet and find out the minimum value for this brand.

The toggle switch is turned to the minimum value.

Turn on the gas supply valve. At the gas water heater, Electrolux and Ariston do this after connecting to the network. The Oasis, Junkers and Bosch gas water heaters are connected when the batteries are installed.

The hot valve is turned on and the device starts working.

How to adjust the water temperature

Turn on the mixer and check the water heating temperature. It must be twenty-five degrees more than the original one. It is worth noting that the water in a gas boiler heats up gradually. The geyser is adjusted using the gas lever.

Reference! You can also adjust the temperature using the water toggle switch. If the flow force increases, the heating temperature will decrease.

Professionals do not recommend heating water above fifty-five degrees. This has a bad effect on the device, as scale forms.

Blood pressure problems

Setting up a geyser requires some time. Accordingly, the result will be visible later. After each stage, it is worth pouring out the water and letting it heat up again so that the values ​​are correct. Low pressure in the device may interfere with normal operation.

If you have problems with blood pressure, you should perform the following manipulations:

• Remove the casing from the device;
• Loosen the locking bolt, use a pressure gauge to check;
• Remove the seal from the adjusting screw;
• Turn on the boiler;
• Set the values ​​to maximum, unscrew the hot water supply taps;
• Adjust the desired pressure.

The Bosch gas water heater, namely its pressure in the nozzles, is regulated in the following way:

• Remove the casing;
• Attach a pressure gauge;
• Loosen the locking screw;
• Attach a pressure gauge to check the pressure in the injectors to the nozzle.

Next, the Bosch gas water heater with maximum thermal power is regulated:

• Remove the seal from the screw;
• Turn on the device;
• Hot water taps are turned on;
• The adjusting screw adjusts the pressure in the nozzles;
• Put the seal in place.

There are brands that have a special “Winter-Summer” mode with temperature adjustment. This handle was made at the bottom of the Ariston gas water heater. Adjustment of the Oasis gas water heater is located on the front panel. The peculiarity of the mode is that in winter the power is higher than in summer. The heating power of the liquid in the column is directly related to the temperature of the inlet stream. In winter, the regulator is set to “maximum”, the heating will be at its highest. In summer, the temperature of the inlet flow is higher and is set to the minimum position. This saves resources.

It is easy to remove bad pressure when checking.

To do this, you must perform the following manipulations if the device has already been used:

1. Pay attention to the rubber membrane. The performance of this part is directly related to the pressure in the line. At the moment the integrity of the membrane is broken, namely when it is exhausted, gas does not flow and the burner does not turn on. The problem is solved by replacing the part.
2. Pay attention to the mesh filter. It is located at the entrance to the water block. The water pressure becomes lower due to debris clogging the part. The problem is solved by cleaning.

How to light a gas water heater

After all diagnostic procedures, the column can be put into operation.

Manually

The manual method was used in older models. In this case, you have to light it with matches.

Advice! You can use regular matches, but fireplace or travel matches are more convenient. They are longer, so the likelihood of getting burned is minimal.

Here you need to perform a number of such manipulations:

• open the water supply connected to the device;
• open the main valve to allow fuel to flow to the igniter;
• light the wick with matches;
• turn on the valve (main) for gas supply.

When igniting for the first time, you should pay attention to where exactly the flame catches, and next time bring the match to a specific place.

Using piezo ignition

We can say that this column is semi-automatic. How to use a gas water heater of this type? It will be enough to press a button to ignite the wick in the combustion chamber. With the help of mechanical force, the spark is transformed - it is enough to ignite the ignition filter. With this method, a number of mandatory requirements must also be met:

• in order to light the main burner, you will need to turn on the main regulator in the fuel supply;
• The ignition filter will remain lit when the regulator is returned to the main position and the water is turned off.

Such designs have a drawback - excessive fuel consumption. Vivid examples of such speakers are the Bosch WR 10-2 P miniMAXX-2, Nevalux 5111, Junkers WR 10-2 PB and other options.

Automatically

The ability to automatically turn on is provided by fully improved modifications that are easy and safe to use even for beginners. The Hydropower system is offered by most modern manufacturers (Bosch, its direct competitor Electrolux and many others). The process of starting work is simplified to the limit.

1. For example, in the Bosch Therm 6000 O, water pressure drives a turbine. It triggers an automatic igniter system inside the device for both the wick and the main burner.
2. The manufacturer Bosch has the Therm 2000 O and Therm 4000 O lines, which carry out electric ignition from batteries (you will need to monitor their service life).
3. The Bosch AM1E series speakers already have a digital control panel that will immediately show all possible switching errors.

The fully automated process has one drawback: many homes have low pressure in the water supply, and this may not be enough for the turbine to operate properly. In addition, such devices are significantly more expensive than their less advanced counterparts.

How to adjust the flame of a gas water heater

Another way to set up a gas water heater is to adjust the flame. On the body of semi-automatic and automatic machines there is a handle designed to adjust the gas. With its help, the supply of blue fuel increases and decreases. The power of the device is directly related to this part.

As soon as the flame becomes larger, the gas consumption will be higher and the water will heat up better. Professionals advise changing the gas transmission speed to properly set the burner. As soon as the burning intensity is selected, the knob for changing the water pressure is applied. In order to change the combustion temperature, it is worth changing the “Winter-Summer” mode.

Adjusting the igniter of the gas water heater will help reduce gas costs in semi-automatic machines. The wick is adjusted using the bolt on the pilot burner. You should be careful when making settings. If you reduce the flame of the gas water heater's igniter too much, the device will stop working. If the flame increases excessively, excess gas consumption will occur.

Setting details

These devices have only one geyser temperature regulator. Thanks to it, the heating temperature and power are adjusted. The self-diagnosis system evaluates the operation of the components when turned on. If there are problems, the red light comes on and the device is blocked from starting. Then it is necessary to adjust the water pressure.

Then you need:

• Remove batteries from the compartment;
• Turn off the microswitch;
• Provide a source of electricity;
• Turn on the hot tap and turn on the microswitch;
• The pressure on the burner should be maximum;
• After saving the settings, the orange lamp will turn on.

In other columns, the water temperature is adjusted by turning the toggle switch and controlling the strength of the water flow.

Important! When adjusting, it is prohibited to exceed the maximum temperature specified in the instructions.

Unfortunately, it is impossible to easily set the settings according to the instructions. Each system has different meanings. If you have difficulties setting up the gas water heater temperature regulator with your own hands, you should turn to professionals.

Popular models

produces several different models of gas water heaters. All of them are characterized by reliability and ease of operation. But there are slight differences.

Electrolux GWH 265 ERN Nano Plus

This speaker has simple mechanical controls and low power. But it is capable of providing hot water to a city apartment and has sufficient performance so that 2 water supply points can be connected to it. The Nano Plus column has compact dimensions and an affordable price. Oxygen Free technology prevents the release of harmful substances during operation.

The model is popular due to its low cost and ease of operation.

But some users note insufficient power when several water intake points are turned on, as well as difficulties in finding spare parts.

Electrolux GWH 275 SRN

This water heater is characterized by reliability. The modulating burner ensures that the desired temperature is maintained regardless of the water pressure. A special feature of this speaker is piezoelectric ignition. It turns on after pressing the button.

The presence of 2 modes and automatic adjustment allows you to maintain the desired temperature. A multi-level protection system ensures uninterrupted operation and shuts down the device when the pressure drops or there is no traction.

Electrolux GWH 285 ERN NanoPro

The design of this model is simple and reliable. Its special feature is the presence of the INVERTER Control system, which ensures smooth adjustment and quick start-up. The heat exchanger is made using innovative technology that protects it from any negative influences. A convenient digital display allows you to monitor the temperature, flame level, and water pressure.

The universal diameter of the chimney allows you to install the column in any room. The main advantages of the model are four degrees of protection and quiet operation.

Additional Information! The model was developed for regions experiencing water shortages and gas pressure problems. It can work even with low pressure.

Electrolux GWH 11 PRO Inverter

Quite a powerful water heater, suitable for both a city apartment and a large private house. You can connect several water intake points to it. It has an automatic heating level system depending on the water pressure.

A multi-level security system provides protection against overheating, chimney clogging, and turning on without water. The convenient display shows not only the temperature indicator, but also the flame level, battery charge, and water pressure.

Poor pressure

Let's look at what affects the water pressure in a gas water heater:

1. Presence of blockages. Every pipe through which water moves tends to become clogged with debris. If we take an Electrolux geyser as an example, the blockage occurs in the mesh filter filled with lime and rust. If the water flow is low, the pressure will be minimal.
2. Engineering works. In this case, scale appears inside the heat exchanger. When the water is shut off and the water unit of the gas water heater resumes operation, a “water hammer” occurs, after which some of the scale penetrates into the mixer and forms a blockage.
3. Device power. For Bosch geysers and other models, the power of the device is important. It will create good pressure in the system. If the power of the device is less than eight, then the pressure will be minimal. For good operation of the geyser water unit, it is worth purchasing a device with a power of eight to ten kilowatts.
4. Scale. It usually occurs in metal containers in which water is brought to a boil. In a gas water heater, the heat exchanger is considered a tank. With hard water, scale forms on its walls, which subsequently moves into the tubes, due to which the pressure decreases.
5. Preventive actions. Any device, including a geyser, needs regular maintenance, namely the prevention of blockages. In most cases, a decrease in water pressure occurs due to careless use of the device.

Features of work

Thanks to the simple design of Electrolux speakers, they are easy to use. Most of them turn on automatically after the hot water tap opens. The gas unit is activated and the burner lights up. It heats the water pipes, so hot water appears in the tap within 15 seconds. After the tap closes, the burner goes out.

The design of the speakers is thought out to the smallest detail; there is nothing superfluous in it. This design ensures reliable operation.

How to solve a problem

If the filter is clogged, you should remove this part from the device. Clean it with a stiff brush and water. If, during cleaning, a violation of the integrity of the filter is noticed, it is worth replacing the part with a similar one.

If the hot water pipe is clogged, you should run cold water in the opposite direction. The plug is removed, a container is placed under the device under water and both taps are turned out. The spout is closed with your finger. It is considered possible that cold water will push the clog forward.

It is not recommended to use chemicals that remove scale from the column. Their composition can easily destroy the metal surface. The best option is to use citric acid, which is dissolved in hot water.

If the blockage has advanced further than the pipes, it can easily penetrate into the faucet. The most “vulnerable” places where blockages mainly appear are considered to be a thin rubber hose, a filter and a faucet. The problem can be solved by disassembling the mixer and performing a thorough inspection. Dirt is removed using running water.

What malfunctions do the Neva Lux dispenser have?

The display of the Neva Lux geyser indicates an error code when problems occur.

Common fault codes that also occur at the Neva Transit gas water heater:

E7. After seven attempts to turn on the device, it goes out or does not work at all. The problem lies in the failure of the electric valves, the accumulation of soot on the electrode, the mixing of the ionization sensor, or the gas block boiling. The solution is to replace faulty parts or clean the soot with a brush.

L0. Insufficient fuel supply.

Causes:

• Poor water pressure;
• Decrease in temperature;
• Exceeding the pressure of the gas water heater Neva Lux.

The problem can be solved by adjusting the temperature, installing a reduction gear and descaling the radiator.

E0. The device turned off on its own. Fuel does not move into the device. The solution is to check the gas valve of the Neva Lux gas water heater. In most cases, the gas supply stopped for some time.

E8. Malfunction related to the traction sensor. It is usually associated with a clogged chimney or a broken sensor. The solution is to clean the chimney from soot yourself or with the help of utility services, or replace the sensor with a new one, as well as check the tightness of its contacts.

Other device problems

In addition to error codes, there are other malfunctions that are also typical for the Neva Transit gas water heater:

1. The appliance is too noisy. In this case, you should start turning the water regulator and reduce the pressure.
2. The gaskets “stick out” in the pipe connection areas. The problem is solved by replacing the element.
3. The display has stopped working. The problem lies in faulty contacts, a broken display and a faulty temperature sensor. The solution is to replace the parts and the display itself.
4. The device stopped lighting up. This problem is also typical for the Zanussi gas water heater. The malfunction lies in membrane stretching, overheating and a broken device element. Solved by replacing the part with a new one.

When repairing with your own hands, it will take a long time to study the repair material and actually set up the gas water heater. The result the first time may not be the same as in the repair instructions in the literature and may even be disastrous. The best option would be to entrust the matter to professionals.

Source

Preparatory work

Despite the fact that each column “Selena”, “Vector”, “Bosch”, “Neva” comes with instructions indicating the settings, not all users understand them. One mistake at the beginning - and the technology does not function as it should.

Work begins with adjusting the water. If you do not do this right away, then all settings will be inaccurate. The flow should be minimal. The nominal values ​​are indicated in the documents, but they are general: 6, 10, 12 liters.

How to set the hot water regulator:

• Open the hot mixer to full power. When connecting to several intake points, only one valve can be unscrewed.
• Using the water switch, set the desired value.
• Turn on the tap.

Follow the recommendations of experts:

• Wait until the pressure in the line decreases, but the column will still turn on.
• Turn the water toggle knob to the maximum position.
• Turn the gas regulator to the minimum mark until the temperature suits you.

To finish cooking, you need to adjust the gas supply. Check the data sheet again to find out the minimum value for your model.

• Turn the toggle switch to minimum.
• Open the gas valve. In the Ariston and Electrolux models, this must be done after connecting to the network. In Oasis, Dion, Bosch, Junkers heaters - after installing batteries.
• Open the hot valve and the column will start working.

Installation of Astra water heater

The Astra heater is equipped with two hooks and handles. To attach it to the wall, drive in dowels in the pre-marked places, strengthen the hooks, and hang the column vertically. The wall must be made of non-combustible materials.

Next, you should disconnect the display connectors, disconnect the indicator on the front panel, remove the latch from the front side of the device, and remove the front and side panels.

Connect to the gas pipeline using a tee that fits into the main line and a tap is screwed to it. Drill holes in the wall along the path of the pipe and secure the clips there. Connect it to the unit by placing it in the clips. It is permissible to use a bellows hose as a gas hose; there is no need to attach it to the wall. Be sure to install a tap in front of the device that turns off the device after finishing work.

Then attach the supply and outlet water pipes to the device’s nozzles. Place a mechanical filter and shut-off valve on the supply. Check the tightness of fasteners. When connecting, pipes with a diameter of ½ inch are used. During installation, hold the device fittings with a second wrench. To extend the service life, the manufacturer recommends installing an anti-scale device if very hard water is used.

Check the draft of the chimney, connect the device pipe to it, make sure that the pipe fits tightly to them, otherwise there will be a carbon monoxide leak. The length of the vertical part must be at least half a meter.

Check pipe connections. Water pipes are checked by opening the cold water shut-off valve, gas pipes are checked by soaping. If a leak is detected, fix it by tightening the nuts.

Insert the batteries into the compartment observing the polarity, start and configure. Before the first start-up, the device must be at room temperature for at least an hour. Then install the panels, LED indicator, block handles.

If desired, instead of battery power, you can reconnect to a 220 volt electrical network. To do this, you should purchase a power supply and connect it to the battery terminals, observing the polarity.

The dispenser can operate on liquefied gas, i.e. from a gas cylinder, nozzles for connecting it are purchased separately.

How much does it cost to connect? Domestic units such as Astra, Neva, Ladogaz can be installed starting from 1,500 rubles.

Adjusting the water temperature

Open the mixer and evaluate the heating temperature of the water flow. It should be 25 degrees higher than at the entrance. Keep in mind that the gas boiler does not heat the water immediately, you need to wait a little. Use the gas lever to adjust.

You can also adjust the temperature using a water toggle switch. By increasing the flow force, you reduce the heating temperature, and vice versa.

Experts do not recommend heating above 55 degrees. This negatively affects the operation of the device, since scale is actively deposited.

The settings take some time, so you don’t need to wait for the results right away. After each stage, you need to drain the water and let it heat up again to check the accuracy of the indicators. Operation may be hampered by reduced pressure in the system.

If the device runs on liquefied gas and there are problems with pressure, do this:

• Remove the device casing.
• Loosen the locking bolt and measure the readings with a pressure gauge.
• Remove the seal from the adjustment screw.
• Start the boiler.
• Set the maximum values, unscrew all hot water faucets.
• Set the required pressure.

Some models are equipped with an additional “Winter-Summer” mode. The heating power of the water in the column depends on the temperature of the inlet flow. In winter, the regulator is set to the “maximum” position - maximum heating. In summer, the inlet temperature is higher, so the value is “minimum”. This saves resources.

Problems with poor water pressure can be corrected by checking. If the equipment has already been in operation and you decide to reconfigure it, but there is no pressure:

• Check the rubber membrane. Its operation depends on the pressure in the line. The membrane bends and the gas valve is activated. When it wears out or becomes deformed, the gas supply does not start and the burner does not light up. Replace the membrane.
• Mesh filter. Located at the entrance to the water reducer (block). It becomes clogged with small debris from the water supply, so the pressure may decrease. Clean the part.

Nuances of operation

Let's look at frequently asked questions when using geysers.

Why does the geyser turn on or not turn off on its own?

Spontaneous turning on of the column can occur if there is a leak in the hot water system behind the column. Accordingly, solving the problem with the water supply eliminates the problem with the column.

Much more often this situation arises: the column continues to work even when the tap is turned off. This happens due to incorrect operation of the diaphragm (it loses elasticity), which is installed in the water regulator. After the user turns off the hot water, it cannot take the desired position; it presses the gas supply sensor for some time. In this case, only replacing the worn part will help.

If the membrane loses elasticity, the column may not turn off

Is it possible to turn on cold water when the water heater is on?

Many users are lazy, do not know how or do not want to set comfortable settings on their column, and regulate the water temperature by adding cold water to it. You can't do this, here's why:

• this is prohibited in the user manual;
• When mixing water, scale appears on the heat exchanger, which spoils it.

Advice! More advanced models of columns have a “winter-summer” option, which allows you to quickly change the outlet water temperature.

Do I need to turn off the speaker at night?

In older speaker models, as well as in those with piezo ignition, the wick burns constantly. This, on the one hand, is not economical, since gas is constantly being consumed, but on the other hand, it is potentially dangerous. It is better to turn off these speakers at night and sleep peacefully.

There is no need to turn off a modern gas water heater

Modern gas water heaters have an automatic ignition system. There is also a whole set of hardware responsible for security:

• traction sensor;
• flame sensor (monitors its presence);
• The temperature sensor allows you to keep it up to 90 degrees.

An alarm from any of them leads to immediate shutdown of the column. This column can not be turned off. Usually this point is not even written down in the manual.