how to make a stove in the garage using antifreeze

How to make heating in a garage using antifreeze?

There are many ways to effectively heat your garage.
One of the most effective is the use of a water heating system. Due to their many advantages, the demand for them is quite high. But they have one big drawback - in severe frosts, the water in the pipes can freeze. To avoid this, many garage owners add various antifreezes to the complex. As practice shows, the garage heating system using antifreeze is quite effective. Types of equipping a garage with a heating system with antifreeze as a coolant:

installation of the system from scratch, taking into account the properties of antifreeze;
adaptation of the existing water heating system for the use of antifreeze:

revision of technological connections and joints;
installation of additional radiators;
installation of exhaust ventilation.

Advantages and disadvantages

Attention: Antifreeze does not freeze in heating systems even in severe frosts. This is precisely its main advantage. The maximum that can happen to him is that he will turn into a jelly-like substance. But this will not affect the quality of heating in any way. After all, when heated, it will become liquid again.

Antifreeze can be used effectively in high-temperature circuits, as it has a high boiling point, which is 110-125 degrees. But when choosing a temperature mode, you need to take into account that it heats up more slowly than water.

Antifreeze has not only advantages, but also some disadvantages that should definitely be taken into account.

The disadvantages of antifreeze are:

High viscosity compared to water. To pump it through pipes, additional power will be required. The circular pump will need to be replaced with a more powerful one.
The heat capacity of this coolant is 1-15% lower than that of water. To compensate for this, it will be necessary to install additional radiator sections, heat exchangers, etc.
High fluidity, which requires good sealing of all connections on the heating system. Rubber gaskets should be replaced with paronite gaskets.
The service life of antifreeze, like many other antifreezes, is no more than 5 years. After which, it needs to be completely replaced.
When stagnant, it forms white flakes, which, when settled, can ruin the heating structure.

Antifreeze has one more drawback. The most significant. It's poisonous. It is necessary to use this composition in the heating system so that it cannot enter the room. The heating system must not have any leaks and be sealed at the connections. After all, as already mentioned, the fluidity of this substance is greater than that of water, and it can leak even through a minor crack.

A leak of antifreeze is not immediately detected, and in order to avoid inhaling its vapors, which easily escape under the influence of high temperatures, you should carefully consider the condition of the heating system and inspect it from time to time for any damage.

Attention: If a leak is detected, you should immediately fix it, ventilate the garage and thoroughly wash the floor.

In addition, under no circumstances should it be poured into the heating system if a double-circuit boiler is used, since the substance can easily get into the hot water circuit and the consequences of this will be very unpleasant.

Filling the heating system

If you are not afraid that antifreeze is poisonous and you decide to pour it into the heating rack, you need to fully comply with safety precautions both when pouring and during subsequent operation.

Remember, before pouring, the antifreeze should be diluted. It should not be used in concentrated form, as it can cause damage to the heating boiler and circulation pump. When diluting antifreeze, you can independently choose the desired ratio of water and antifreeze. But first you should find out the lowest temperature at which its crystallization is possible. Most often, such information is available on the packaging.

Attention: Before pouring antifreeze, you should select the correct temperature conditions. Its name indicates the temperature at which its crystallization occurs. For example, A40-M (-40 degrees). Please note that the finished coolant should not be diluted with water. It is necessary to use concentrates that consist of 95% ethylene glycol. Using it for pouring, you can independently select the desired ratio of concentrate to water.

When diluting it with water, it should be taken into account that if it freezes at a temperature of -40 degrees, then the ratio of water and concentrate should be 1:1. At freezing temperature - 30 degrees 2:3. And if freezing occurs at -20 degrees, the ratio is 1:2.

Before pouring it into the heating system, all existing coolant should be drained from it, and the radiators and pipes should be thoroughly rinsed. All internal contamination must be removed. It is best to wash several times to achieve better results. If any antifreeze was previously poured into the system, it must be completely drained. You should not mix it with the antifreeze you are pouring.

The system used to heat a garage using antifreeze requires sealing the heating system and replacing rubber gaskets. If necessary, detected violations should be corrected. Pressure testing must be carried out, which is necessary to check the heating system for possible excesses of normal pressure. Thanks to this procedure, hidden defects can be detected.

But first you should find out the quality of the concentrate to find out whether it can be poured into the heating system. To find out, make a solution in a small glass container and leave it for several days. The temperature should be room temperature. If no foam or sediment forms, it can be used. Otherwise it should not be used.

Only after all these procedures, using a special pump, should you start pouring antifreeze. This should be done carefully.

Attention: Be sure to use a protective suit, respirator and gloves. The garage should be well ventilated at this time. If it gets on your skin when pouring, you should immediately wash it off with water. If you have a chemical burn, consult a doctor.

Results

Antifreeze is the same ethylene glycol antifreeze. Antifreeze can be used in a heating system if you are careful. In permanent residences, it is better to abandon this idea; there are too many pitfalls. Do not forget that antifreeze is very toxic. Therefore, under no circumstances should it be used in systems with a double-circuit boiler. You should also remember the operating rules (do not overheat, do not breathe in vapors, do not take orally, change on time). Undoubtedly, by pouring antifreeze into the circuit, you will save twice as much as compared to non-toxic foreign propylene glycol compounds. But are these pennies worth the risk? The question is rhetorical.

In the modern world, a car is a necessary accessory for every second family. Taking care of its technical condition, it is necessary to carefully consider the nuances of operation in the cold season.

If you don’t plan to freeze your car for the entire winter, the best option is to purchase and properly prepare and operate a garage. It consists, first of all, in the correct insulation of this structure, and, secondly, in the installation of an optimal heating system.

The most suitable types of garage heating are gas and electric systems. They, in turn, can be of two types, which differ in the structure and presence of communications:

Heaters of forced-air or circulation action with air coolant. These are local heat sources that do not require serious installation.
Circulation systems with liquid coolant. Such systems contain additional communications in the form of pipes, radiators and a pump for pumping coolant. The latter is usually water or antifreeze.

Antifreeze is a relatively viscous bluish liquid used in vehicles of any type as a coolant for the engine cooling system and interior heating system.

This liquid contains ethylene glycol, which is a highly toxic substance in any state of aggregation. Contact of ethylene glycol with skin can lead to tissue burns , and inhalation of vapors causes damage to the mucous membranes of the respiratory system, disruption of brain function, and even death.

In its normal state, at room temperature, antifreeze is not dangerous ; toxic substances are blocked by special additives included in its composition. When exposed to excessive heat, the additives are destroyed and the coolant becomes dangerous. This happens at temperatures above 90-100 degrees. That is why manufacturers prohibit the use of antifreeze for use in heating systems.

special liquids on the market for use as a coolant when heating residential and commercial buildings. Instead of ethylene glycol, they use propylene glycol as an active substance, which is not hazardous to health. The cost of such formulations is two to three times higher than the cost of antifreeze.

Heating system

Heating your garage with antifreeze requires the installation of larger radiators and a more powerful circulation pump. In addition, attention should be paid to installed radiators and pipes. Since antifreeze and many similar antifreezes are made on the basis of ethylene glycol, you should find out in advance whether they can be used as a coolant in the presence of aluminum or bimetallic radiators and galvanized pipes.

Types of antifreeze: green, red, blue. Which one to choose - the differences and effects of each on the metal of the heating system and components.

Otherwise, the antifreeze used may have a negative impact on the heating system, for example by causing metal corrosion.

Before pouring antifreeze, be sure to make sure that it will not cause harm to your heating system. Also, consider the risks and costs associated with its operation. Please note that the lower the concentration of coolant, the less likely it is to get burned if it gets on your skin.

Antifreeze can be used quite effectively for heating a garage. Its use allows you to achieve warmth in it and avoid freezing of the system even in severe frosts. But it should be used with caution, as it is very toxic. When using it, you must follow safety rules. Do not use it under any circumstances if you have a double-circuit boiler.

Heating system

The heat supply to your garage with antifreeze requires the installation of larger volume heating devices and a more powerful circulation pump. Moreover, it is necessary to pay attention to the installed heating devices and pipes. Since antifreeze and many similar antifreezes are made on an ethylene glycol basis, you should find out in advance whether they can be used as a coolant if there are metal or bimetal radiators and tin pipes.

Types of antifreeze: green, red, blue. Which one to choose - the differences and influence of each on metal heating systems and components.

In another case, the antifreeze used may have a bad effect on the heating system, for example, causing metal corrosion.

First of all, before pouring antifreeze, you need to make sure that it will not cause damage to your heating system. Moreover, take into account the dangers and costs associated with its operation. Keep in mind that the lower the concentration of coolant, the less likely it is to get burned if it penetrates the surface of the skin.

Antifreeze can be used quite well for heating a garage. Its use makes it possible to achieve warmth in it and avoid freezing of the system even in severe frosts. But it must be used carefully, as it is very poisonous. When using it, you must follow safety rules. Just don’t use it if there is a double circuit.

The best heating in the garage

Main types of garage heating

The choice of heating system and type depends on the location of the garage. If the building is located near the house or on site, with a gas pipeline connected, in this case everything is simple; by installing a gas boiler, you can install a pipeline and install heating devices.

If you need to install heating in a garage cooperative, such a system can be equipped using:

an expensive system with electrical appliances or a boiler;
heating from a gas boiler powered by cylinders. This is not the cheapest method; you will need to spend money on refilling cylinders;
using wood or coal as fuel will require the allocation of space in the garage for fuel storage. But this scheme is the cheapest and it is possible to make a furnace with a water circuit yourself if you have skills in electric welding;
An expensive universal means for heating a garage - an electric - wood-burning boiler for heating. This scheme is available when installed in several bays of car repair shops;
The cheapest and most accessible way to heat a garage with water is a homemade or industrial stove that runs on used motor oil. Such fuel is available, does not take up much space in the garage, and a system filled with antifreeze will not defrost even at significant sub-zero temperatures.

In any case, if you need to make water heating, it is better to fill the system with antifreeze. We'll talk about its positive and negative sides in the next chapter.

It is important to know! In the worst case, at a very low, prohibitive temperature, antifreeze turns into a jelly-like mass. It easily turns into liquid when the boiler is turned on.

Water heating

Along with ease of manufacture and efficiency, the potbelly stove also has one significant drawback: it cools quickly after the fuel burns out. To improve the efficiency of stove heating, it is recommended to build a water heating circuit.

To organize water heating of the garage you will need:

Install heating devices throughout the room.
Connect pipes to them.
Hang a special expansion container at the top.

It is advisable to fill the system pipes with antifreeze, which will make it possible not to be afraid of defrosting in the event of prolonged heating downtime in winter weather.

Types of water circuits:

Single-pipe . In this case, the coolant passes through all parts of the system, in a circle.
Two-pipe . Here the heated water is supplied in the return pipe in a cooled form.

Single-pipe circuits are considered cheaper to install, however, such a circuit will have different temperatures in different areas. Strictly speaking, this is not critical for a garage. The heating device must be placed lower than the pipes: only in this case will water or antifreeze circulate normally. The movement of the coolant will be stimulated by heating from the potbelly stove.

If installing the stove below the entire system is not possible, a circulation pump will be required. Since heating of the coolant is usually accompanied by an increase in its volume, the highest point of the system is equipped with an expansion tank. Such circuits are volatile. If the power supply to the garage is unstable, it is better to get a 12 V circulation pump powered by a battery.

Two-pipe autonomous heating systems for garages are recommended for use in large spaces. In addition, in this case, you can also use heated floors, which involves laying special coils, followed by filling them with a concrete screed. The most significant disadvantage of a two-pipe system is the risk of it defrosting during irregular use.

To avoid such situations, antifreeze is poured into the circuit. For these purposes, special solutions based on glycerin and other chemical components are used: this will increase the durability of the system by an order of magnitude. The joints of a circuit filled with antifreeze may only be insulated with special sealants. Ordinary tow will come apart within a short time, and the pipes will begin to leak. Do-it-yourself heating in the garage using antifreeze is arranged according to the same scheme as water heating.

The main advantages and disadvantages of a system filled with antifreeze

The advantages of the method include:

The boiling point of antifreeze is 1100-1250, so it is preferable to use it in individual heating systems with high fuel combustion temperatures. At the same time, the air in the room will heat up more slowly, so this feature of the coolant must be taken into account;
prevents the formation of scale on the walls of boilers, and accordingly increases the service life of the equipment;

A heating system in a garage filled with antifreeze has its negative aspects, which include:

a higher level of viscosity will require the installation of a powerful circulation pump;
Antifreeze has a low level of heat capacity; to achieve a level of room heating similar to water heating, it will require the installation of additional sections on radiators;
high penetrating ability of antifreeze requires tightness of all wiring connections;
for gaskets you will have to use expensive paronite;
water heating of a garage using antifreeze as a coolant will require a complete replacement of antifreeze in 4-5 years;
the most important disadvantage is its toxicity to humans. Therefore, it is important to make the heating circuit completely sealed and monitor this constantly.

Important! For optimal, safe operating conditions of a boiler with a water circuit filled with antifreeze, it is important to choose the right coolant according to its composition. It is not recommended to dilute the finished antifreeze with plain water before filling the system. In this case, the freezing point of the liquid changes. Only special concentrates can be diluted, but strictly according to the instructions. Concentrated antifreeze consists of 95% propylene glycol.

The main way to properly prepare coolant for a garage heating system

The most popular for heating is concentrated antifreeze, with certain characteristics. In this case, using the instructions, you can prepare the antifreeze that is most suitable for your climate zone. Another advantage of this solution is that counterfeit ready-made antifreezes and antifreezes are most common on the market. But you should remember - the coolant is diluted only with distilled water.

First of all, you should determine the required maximum subzero temperature, after which the composition thickens and crystallizes. This can be achieved by proceeding according to the following scheme:

when combining antifreeze and water in a ratio of 1/1 – the freezing point is 400 degrees below zero;
if it is required that the coolant does not crystallize at -400 - in this case, the mixture is diluted 2/3;
taking 1 part of the concentrate, adding 2 parts of the distillate - we get a coolant that does not freeze at -200.

To check the quality of the concentrate, you can do the following:

dilute a small volume of the mixture in a certain proportion;
pour it into a transparent glass container;
leave the solution in the garage for several days at above-zero temperatures;
inspect the solution if sediment has formed or foam has formed - it is not recommended to pour such antifreeze into water heating in the garage. Such formations indicate low quality of the concentrate.

When using a combination stove or boiler for a garage with antifreeze filled, it is important when replacing not only to properly dilute the concentrate, but also to fill the system with it.

Pour antifreeze into the garage water heating

To do this, you will need to prepare a garage heating system with your own hands. This is not a difficult, but responsible operation. We remove water from pipelines and registers. It is important to note that waste coolant cannot be poured under plants or onto the ground. It is better to collect it in containers and drain it into the storm drain.

Further operations are performed in the following order:

It is important to rinse the pipes and radiators thoroughly; to do this, close the drain valve and fill the system with clean water. You can add citric acid, this treatment removes alkaline scale from pipes. After starting the boiler, heating the water, let it cool slightly and drain. The operation should be repeated several times.
When filling with water for the last time, be sure to check all pipes, joints and registers for leaks and fistulas. When they are detected, such places are cleaned and boiled or crimped with clamps with paranitic gaskets. At all connections where there are rubber seals, it is necessary to replace them with paranit.
After these operations, having filled the system, turn on the boiler, bring the temperature to operating temperature and check the tightness of the connections. Some experts advise pressure testing of the heating, but this is unnecessary, we do not have prohibitive pressures.
Now pour liquid into the heating. It is important to do this evenly, in a small stream. You already know the optimal volume of antifreeze to fill the garage heating system. Remember that after filling the system, it is necessary to remove any air pockets from it. This is done at the top point of the system using a tap or it is equipped with an expansion tank.

Now you can start the boiler and once again check the tightness of the joints and the absence of air in the liquid heating system of the garage. It is important to remember that antifreeze is a toxic material. If the substance gets on the mucous membranes, they should be immediately rinsed with water. Carry out work with the gates of the box open.

In conclusion, some advice.

You can heat a garage using a potbelly stove or stoves, but fumes, smoke and space for storing firewood make this method costly and inconvenient. You don’t have to be smart and install an electric convector or boiler, but this technique significantly increases the figures on your electricity bill.

Regardless of the choice of types of liquid heating in the garage, we recommend using antifreeze as a coolant. Good luck.

How can you heat a garage?

So, we are talking about autonomous heating of the room, therefore, we need to choose the principle on which the heating system will operate. If earlier the conversation was only about a banal potbelly stove, now the choice of suitable devices is so wide that we will divide them into several categories.

The most economical ways to heat a garage with electricity

This type of heating is the first option that comes to mind. Indeed, the choice of electrical heating devices is very large. Such units are characterized by high efficiency and reasonable price. And what’s important: they don’t require you to stock up on fuel; it’s always in the electrical wiring.

The first possible method is to use a fan heater or heat gun. In both cases, it is a very compact device that takes up little space in the garage. Install the electric heater for the garage on the floor or on a workbench.

The fan heater heats up a small garage in a matter of minutes, driving air through hot heating elements

The only thing that will bother you is the smell of burning dust and the noise of the fan.

Another option is to use a convector. This method is considered more effective. In addition, convectors can be used in rooms with high humidity. A small, neat convector can be mounted on the wall or moved around the garage on wheels.

This type of heater is convenient because its power is easy to regulate.

Convector type heater. In this publication we will look at the design of convectors, their types, advantages and disadvantages, the secrets of choosing the right one, and a review of popular models and manufacturers.

An electric floor is also a good idea. If you lay the heating cables evenly over the entire floor area, the garage will always be warm. The air temperature can be adjusted using a thermostat. The only thing that is important in arranging such a system is the use of durable materials that can withstand the weight of your car.

Infrared heating is gaining increasing popularity among owners of residential and non-residential premises. The operating principle of the IR heater is based on the effect of infrared rays on the surface. Everything that comes into the field of action of the device heats up and gives off heat to the air.

Important! Keep in mind that IR radiation has a negative effect on car paint. For this reason, it is better not to install this device directly above the car.

Some tips for installing electric heating in the garage:

all wiring must be insulated using a plastic or metal box;
Do not use wiring with aluminum content, it is very fragile;
Sockets in the garage must be grounded and protected from moisture. Don't install them too low to the floor;
It is better to place the switch for the inspection hole at the top.

A method of water heating in a garage without using electricity

The traditional water heating scheme is as follows: it includes a boiler, a system of pipes and radiators, and an expansion tank. When solving the problem of how to heat a garage in the cold season, consider installing a water circuit. This type of heating is good because the heat in the room is retained for a very long time.

For the water circuit, you can use a single-pipe or two-pipe circuit. In the two-pipe version, heat is evenly distributed over the entire area. Schemes of water heating in the garage for DIY installation with natural and forced circulation:

Antifreeze garage heating system

A garage often performs several functions for its owner. In addition to its main purpose of storing the car from intruders and natural disasters, it also serves as a repair area and a warehouse for spare parts, fuel and lubricants, and often a resting place. If it's summer outside, there are no questions. Open the gate, turn on the carrier and repair as necessary. But if the temperature outside is very sub-zero, then you can forget about a comfortable pastime or work. And it’s worth thinking about how to build heating in a garage using antifreeze with your own hands, if no other decisions have been made.

Solution options

There are four types of garage heating systems, differing in the fuel used in them:

electric;
gas;
liquid fuel;
on solid fuel.

Let's look at the design features of each of them - you will see different heating systems in the garage in the photo.

Gas heating system

Not the best solution is autonomous heating of the garage with gas, if the question is about heating a detached garage. There are several reasons for this. First of all, there are very strict rules put forward by gas company employees. If you decide to install gas heating in your garage, be prepared for regular inspections. In addition, not all garages have the possibility of connecting to a gas pipe.

Advantages and disadvantages of using antifreeze in a heating system

The main reason why antifreeze is poured into the garage heating system is that in this case there is no need to worry about the batteries defrosting during severe frosts. The crystallization threshold of antifreeze is much lower than that of ordinary water. Depending on the brand, it does not freeze at -20, -30 and even -40 degrees. Antifreeze, of course, may thicken somewhat, but this will have absolutely no effect on its qualities and when heated it will quickly turn into a liquid state again. At the same time, its boiling point is higher than that of water, so in this respect it is safer.

However, there are many more disadvantages, or more precisely, some inconveniences, of using antifreeze in a garage heating system installed with your own hands. It’s worth mentioning right away that these inconveniences relate rather to the process of assembling the system, during which it is necessary to observe certain safety measures and take into account the properties of this non-freezing liquid. All of them are worth listing and explaining a little:

Viscosity. This property of antifreeze, which is much higher than that of water, requires the installation of a more powerful circular pump.
The heat capacity, on the contrary, is much lower. That is, when the water heats up to 30 degrees, the antifreeze under the same initial conditions will only reach 20-25 degrees. And this can only be compensated for by installing additional radiators.
Fluidity. This component is also high-grade, which means you will have to carefully check the system for cracks in order to avoid the slightest leak.
With a long absence of circulation, in other words, stagnation of liquid, flakes can form, which, settling, can render the entire heating system unusable.
Lifetime. Antifreeze will serve as a garage heating liquid for no more than five years. After this, you will have to drain it, thoroughly rinse the entire system and fill in a new one.
And the main disadvantage of antifreeze is that it is poisonous. And not only the liquid itself, but also its vapor. And under the above-mentioned condition of increased fluidity, the possibility of it leaking and entering the atmosphere of the garage is very possible. If this problem is detected, you should immediately eliminate the cause of the leak, thoroughly rinse and ventilate the room.

There are many more disadvantages. However, this does not mean at all that you should forget about a garage heating system using antifreeze, installed by yourself. It’s just that all work on the installation of heat exchangers, heating radiators and pipes needs to be carried out more carefully and in compliance with all safety regulations.

How to make garage heating with your own hands cheaply and quickly: choosing the right place

The location for installing the equipment is selected taking into account fire safety. Heating appliances powered by gas can be used in rooms with excellent ventilation. In addition, it is important to consider the chimney device. The selected device should be attached to the main wall. It is important to correctly calculate the performance of the hood. It is important to provide free access to heating equipment.

Fireplace stoves provide not only high-quality heating, but also an aesthetic appearance

Note! When using hearths with an open fire, do not close the vent until the fuel has completely burned out. You must remember to turn off heating devices for the garage at night.

Using an economical heating method will allow you to fully use the garage at any time of the year.

Heating in a garage using antifreeze - installation details

Installation of the entire heating system begins from the stove.

Based on our preferences and capabilities, we install a heating device in the selected location. Electric or gas boiler. A stove that runs on wood, exhaust or another type of fuel.
We hang aluminum or cast iron radiators in such a way that the heating of the entire room is uniform.
Pipes for connecting radiators to the stove should be selected taking into account the viscosity of the antifreeze. That is, their diameter must be at least 1.5 times larger than for water heating.
The circular pump is installed in the system at a distance of at least 1 meter from the heating device. It is recommended to install shut-off valves on both sides. This is done so that it is possible, if necessary, to remove the pump, without having to drain the antifreeze from the entire system. The pump itself should be selected so that it is twice as powerful as when used in a similar heating system operating on water.
We install the expansion tank as high as possible. The ideal option would be to take it to the roof
Carefully connect all elements. It is better not to use threaded connections. This is due to the increased fluidity of antifreeze, which easily seeps through such connections. But a high-quality welding seam will easily hold it.
Filling the antifreeze system is carried out as follows:
Approximately 2/3 of the required volume is poured into the expansion tank.
The circulation pump turns on.
You should drive the system a little, carefully monitoring the antifreeze level.
Add if necessary.
After making sure that everything is working properly, there are no leaks and the antifreeze level is appropriate, you should carefully seal the expansion tank.
Now you can start the stove for the first time.
During the first month or two, it is recommended to conduct a daily visual inspection of the entire system, especially the joints and connections for leaks and other faults.

When installing a heating system in a garage using antifreeze, special attention should be paid to ensuring that all elements are made of materials that are neutral to the substances contained in this non-freezing liquid. Aluminum meets these requirements, but it is quite expensive and much more difficult to install. You can use thick-walled iron pipes, especially if your system includes a homemade stove.

Other garage heating options

For regions with frosty and long winters, antifreeze in the garage heating system is the most acceptable option. However, there are other ways.

Water heating. The system is identical to the one described above. Only instead of antifreeze, water is poured into it. Heats up faster. Among multi-level homemade products, one of the simplest. But in case of untimely start-up, it can lead to defrosting of the pipes and complete failure.
Air heating. Probably the only system that does not have significant drawbacks. Installation is no more difficult. Can be left indefinitely without needing to reheat.
Electric heating. Using air heaters, air guns and other devices. Practically safe, but very expensive.
On liquefied gas. A gas heating boiler is required, to which a propane cylinder is connected. Quite an economical option, but there is a risk of fire. It is not recommended to leave a running installation unattended.
Potbelly stove. A small iron stove that consumes all types of solid fuel. Fast heating, good heat dissipation. The disadvantages include the mandatory construction of a chimney and increased fire hazard.

Whatever type of heating system you install in your garage, the main thing is to understand that safety should always come first. Choose a place for the stove away from reserves of fuels and lubricants.

Heating a garage: the most economical way, what to choose

If the outbuilding is located next to the main building, gas heating is often used. In this case, the heating system can be connected to an existing one in the house.

To heat your garage yourself economically, you can use the heating option using different types of solid fuel raw materials. Which can be used as firewood, peat, coal and diesel products. At the same time, you can save on resources, but it is important to think about the storage of raw materials.

A simple potbelly stove can adequately heat a small room

For your information! A simple solution is a gas convector. In such equipment, heat circulation occurs due to convection. The device is connected to a cylinder, but it will need to be refilled every few days.